gcloud alpha compute interconnects attachments l2-forwarding update

Stay organized with collections Save and categorize content based on your preferences.

gcloud alpha compute interconnects attachments l2-forwarding update - update a Compute Engine L2 forwarding interconnect attachment

gcloud alpha compute interconnects attachments l2-forwarding update NAME [--bandwidth=BANDWIDTH] [--default-appliance-ip-address=DEFAULT_APPLIANCE_IP_ADDRESS] [--description=DESCRIPTION] [--enable-admin] [--geneve-vni=GENEVE_HEADER] [--mtu=MTU] [--region=REGION] [--update-labels=[KEY=VALUE,…]] [--clear-labels     | --remove-labels=[KEY,…]] [GCLOUD_WIDE_FLAG …]

NAME

Name of the interconnect attachment to patch.

--bandwidth=BANDWIDTH

Provisioned capacity of the attachment. BANDWIDTH must be one of:

50m

50 Mbit/s

100m

100 Mbit/s

200m

200 Mbit/s

300m

300 Mbit/s

400m

400 Mbit/s

500m

500 Mbit/s

1g

1 Gbit/s

2g

2 Gbit/s

5g

5 Gbit/s

10g

10 Gbit/s

20g

20 Gbit/s

50g

50 Gbit/s

100g

100 Gbit/s

--default-appliance-ip-address=DEFAULT_APPLIANCE_IP_ADDRESS

A single IPv4 or IPv6 address used as the default destination IP when there is no VLAN mapping result found for L2 forwarding. Unset field indicates the unmatched packet should be dropped.

--description=DESCRIPTION

Human-readable plain-text description of attachment.

--enable-admin

Administrative status of the interconnect attachment. If not provided on creation, defaults to enabled. When this is enabled, the attachment is operational and will carry traffic. Use --no-enable-admin to disable it.

--geneve-vni=GENEVE_HEADER

A VNI identier for Geneve header, as defined in https://datatracker.ietf.org/doc/html/rfc8926, used for L2 forwarding.

--mtu=MTU

Maximum transmission unit (MTU) is the size of the largest IP packet passing through this interconnect attachment. Must be one of 1440, 1460, 1500, or 8896. If not specified, the value will default to 1440.

--region=REGION

Region of the interconnect attachment to patch. If not specified, you might be prompted to select a region (interactive mode only).

To avoid prompting when this flag is omitted, you can set the compute/region property:

gcloud config set compute/region REGION

A list of regions can be fetched by running:

gcloud compute regions list

To unset the property, run:

gcloud config unset compute/region

Alternatively, the region can be stored in the environment variable CLOUDSDK_COMPUTE_REGION.

--update-labels=[KEY=VALUE,…]

List of label KEY=VALUE pairs to update. If a label exists, its value is modified. Otherwise, a new label is created.

Keys must start with a lowercase character and contain only hyphens (-), underscores (_), lowercase characters, and numbers. Values must contain only hyphens (-), underscores (_), lowercase characters, and numbers.

At most one of these can be specified:

--clear-labels

Remove all labels. If --update-labels is also specified then --clear-labels is applied first.

For example, to remove all labels:

gcloud alpha compute interconnects attachments l2-forwarding update --clear-labels

To remove all existing labels and create two new labels, foo and baz:

gcloud alpha compute interconnects attachments l2-forwarding update --clear-labels --update-labels foo=bar,baz=qux

--remove-labels=[KEY,…]

List of label keys to remove. If a label does not exist it is silently ignored. If --update-labels is also specified then --update-labels is applied first.

Run $ gcloud help for details.