Tetap teratur dengan koleksi
Simpan dan kategorikan konten berdasarkan preferensi Anda.
Sebelum Anda dapat menggunakan koneksi Cross-Site Interconnect, Google
harus memverifikasi bahwa koneksi Anda ke jaringan edge Google berfungsi. Untuk melakukannya, Google mengirimkan konfigurasi alamat IP yang harus Anda terapkan ke router lokal.
Pengujian yang dijelaskan di halaman ini membantu Anda memastikan bahwa koneksi Anda berhasil diinstal dan menghubungkan port Cross-Site Interconnect ke port router lokal Anda.
Google memeriksa perangkat edge-nya setiap 24 jam, memeriksa lampu di port
ke router lokal Anda. Jika lampu terlihat, maka menunjukkan bahwa koneksi
Anda telah diinstal. Setelah mendeteksi lampu ini, Google akan mengirimkan
email yang berisi alamat IP link-local yang digunakan Google untuk melakukan ping ke router
lokal untuk menguji sirkuit.
Konfigurasikan antarmuka router lokal dengan alamat IP link-local
yang benar.
Contoh berikut menunjukkan konfigurasi alamat IP yang mirip dengan
yang dikirim Google kepada Anda untuk pengujian. Ganti nilai ini dengan nilai
yang dikirim Google untuk jaringan Anda.
Alamat IP link-local Google
Alamat IP link-local router Anda
Ukuran subnet
169.254.0.1
169.254.0.2
/30
Terapkan alamat IP pengujian yang dikirim Google ke antarmuka
router lokal yang terhubung ke Google. Untuk pengujian, Anda harus
mengonfigurasi antarmuka ini dalam mode akses tanpa pemberian tag VLAN.
Google menguji koneksi Anda dengan melakukan ping alamat IP link-local.
Google melakukan pengujian sekali, 30 menit setelah mendeteksi cahaya, lalu setiap
1 jam setelahnya.
Setelah pengujian berhasil, Google akan mengirimkan email yang memberitahukan bahwa
koneksi Anda siap digunakan.
Jika pengujian gagal, Google akan otomatis menguji ulang koneksi sekali per jam
selama 30 hari.
Menggunakan koneksi Cross-Site Interconnect
Setelah semua pengujian lulus, koneksi Cross-Site Interconnect Anda siap digunakan, dan Google mulai menagihnya. Untuk melihat status koneksi, lihat Melihat detail koneksi.
Pada tahap ini, hapus alamat IP pengujian dari antarmuka atau antarmuka di
router lokal Anda. Untuk mengonfigurasi ulang router untuk produksi, lihat
Mengonfigurasi router lokal.
Koneksi Anda sekarang dapat membawa traffic, dan Anda dapat membuat jaringan lintas situs.
[[["Mudah dipahami","easyToUnderstand","thumb-up"],["Memecahkan masalah saya","solvedMyProblem","thumb-up"],["Lainnya","otherUp","thumb-up"]],[["Sulit dipahami","hardToUnderstand","thumb-down"],["Informasi atau kode contoh salah","incorrectInformationOrSampleCode","thumb-down"],["Informasi/contoh yang saya butuhkan tidak ada","missingTheInformationSamplesINeed","thumb-down"],["Masalah terjemahan","translationIssue","thumb-down"],["Lainnya","otherDown","thumb-down"]],["Terakhir diperbarui pada 2025-08-12 UTC."],[],[],null,["# Test connections\n\nBefore you can use your Cross-Site Interconnect connections, Google\nmust verify that your connections to Google's edge network are working. To do\nthis, Google sends you an IP address configuration that you must apply to your\non-premises routers.\n\nThe test described on this page helps you ensure that your connection is\nsuccessfully installed and connects the Cross-Site Interconnect\nport to your on-premises router port.\n|\n| **Preview**\n|\n|\n| This product is subject to the \"Pre-GA Offerings Terms\" in the General Service Terms section\n| of the [Service Specific Terms](/terms/service-terms#1).\n|\n| Pre-GA products are available \"as is\" and might have limited support.\n|\n| For more information, see the\n| [launch stage descriptions](/products#product-launch-stages).\n\nFor definitions of terms used on this page, see\n[Cloud Interconnect key terms](/network-connectivity/docs/interconnect/concepts/terminology).\n\nTest a connection\n-----------------\n\n1. Google polls its edge device every 24 hours, checking for light on the port to your on-premises router. Receiving light indicates that your connection is installed. After detecting this light, Google sends you an email containing a link-local IP address that Google uses to ping your on-premises router to test the circuit.\n2. Configure the interface of your on-premises router with the correct\n link-local IP address.\n\n The following example shows an IP address configuration similar to the one\n that Google sends you for the test. Replace these values with the values\n that Google sends you for your network.\n\n3. Apply the test IP address that Google sends you to the interface of your\n on-premises router that connects to Google. For testing, you must\n configure this interface in *access mode* with no VLAN tagging.\n\n4. Google tests your connection by pinging the link-local IP address.\n Google tests once, 30 minutes after detecting light, and then every\n 1 hour thereafter.\n\n - After a successful test, Google sends you an email notifying you that your connection is ready to use.\n - If a test fails, Google automatically retests the connection once an hour for 30 days.\n\nUse your Cross-Site Interconnect connection\n-------------------------------------------\n\nAfter all tests have passed, your Cross-Site Interconnect\nconnection is ready to use, and Google starts billing for it. To view the status\nof your connection, see [View connection details](/network-connectivity/docs/interconnect/how-to/cross-site/view-connections).\n\nAt this stage, remove the test IP addresses from the interface or interfaces on\nyour on-premises routers. To reconfigure your router for production, see\n[Configure on-premises routers](/network-connectivity/docs/interconnect/how-to/cross-site/configure-onprem-routers).\n\nYour connection can now carry traffic, and you can create your cross-site\nnetworks."]]
