Verifique sua cota para garantir que você tenha largura de banda suficiente para o tráfego esperado entre as regiões metropolitanas. Se você precisar de mais cota, solicite um aumento
antes de continuar. Da mesma forma, verifique o limite de largura de banda máxima por fio e solicite uma exceção, se necessário.
Envie um pedido, especificando os detalhes das conexões.
O Google enviará um e-mail de confirmação do pedido a você. Depois que os recursos forem alocados, você receberá outro e-mail com as LOA-CFAs.
Encaminhe as LOA-CFAs para seu fornecedor. Ele provisiona as conexões entre
a borda de peering do Google e a rede local. O Google iniciará automaticamente o teste de nitidez em cada porta alocada após
24 horas.
Quando as conexões estiverem prontas para uso, será necessário conectar
as redes entre si. Para isso,
crie uma rede entre sites nas suas conexões, especificando as propriedades
do cabo ou dos cabos entre as redes, incluindo a largura de banda.
Depois de criar uma rede entre sites com um ou mais grupos de fios, para começar
a enviar tráfego entre seus sites, configure os roteadores locais
para estabelecer conectividade entre eles.
[[["Fácil de entender","easyToUnderstand","thumb-up"],["Meu problema foi resolvido","solvedMyProblem","thumb-up"],["Outro","otherUp","thumb-up"]],[["Difícil de entender","hardToUnderstand","thumb-down"],["Informações incorretas ou exemplo de código","incorrectInformationOrSampleCode","thumb-down"],["Não contém as informações/amostras de que eu preciso","missingTheInformationSamplesINeed","thumb-down"],["Problema na tradução","translationIssue","thumb-down"],["Outro","otherDown","thumb-down"]],["Última atualização 2025-08-12 UTC."],[],[],null,["# Cross-Site Interconnect provisioning overview\n\nThis page describes the steps to successfully create and configure\nCross-Site Interconnect.\n|\n| **Preview**\n|\n|\n| This product is subject to the \"Pre-GA Offerings Terms\" in the General Service Terms section\n| of the [Service Specific Terms](/terms/service-terms#1).\n|\n| Pre-GA products are available \"as is\" and might have limited support.\n|\n| For more information, see the\n| [launch stage descriptions](/products#product-launch-stages).\n| **Note:** For definitions of terms used on this page, see [Cloud Interconnect key\n| terms](/network-connectivity/docs/interconnect/concepts/terminology).\n\nTo create and configure a Cloud Interconnect connection and create\na cross-site network, follow these steps:\n\n1. [Check bandwidth quotas and limits](/network-connectivity/docs/interconnect/how-to/cross-site/check-bandwidth-quota)\n\n Check your quota to ensure that you have enough bandwidth to support your\n expected traffic between metros. If you need more quota, you must request an increase\n before proceeding. Similarly, check the limit for the maximum bandwidth\n per wire and request an exception if necessary.\n2. [Order Cross-Site Interconnect connections](/network-connectivity/docs/interconnect/how-to/cross-site/order-connections)\n\n Submit an order, specifying the details of your connections.\n Google then emails you an order confirmation. After your resources have been\n allocated, you receive another email with your LOA-CFAs.\n3. [Retrieve LOA-CFAs](/network-connectivity/docs/interconnect/how-to/cross-site/retrieve-loas)\n\n Send the LOA-CFAs to your vendor. They provision the connections between\n the Google peering edge and your on-premises network. Google\n automatically starts testing the light levels on each allocated port after\n 24 hours.\n4. [Test the connections](/network-connectivity/docs/interconnect/how-to/cross-site/test-connections)\n\n Follow the recommended steps to verify that your networks are connected\n to Google's network.\n5. [Create a cross-site network](/network-connectivity/docs/interconnect/how-to/cross-site/create-network)\n\n When your connections are ready to use, you need to connect\n your networks to each other. To do that,\n create a cross-site network over your connections, specifying the properties\n of the wire or wires between your networks, including their bandwidth.\n6. [Configure on-premises routers](/network-connectivity/docs/interconnect/how-to/cross-site/configure-onprem-routers)\n\n After you create a cross-site network with one or more wire groups, to start\n sending traffic between your sites, you need to configure your on-premises\n routers to establish connectivity with each other."]]
